[FLASH-USERS] compiling issue--error: too few arguments to function [WINDOWS-1252?] $B![ (B5Dopen2? size=

[Ken Chen]

Hi Chris and all:
It did work. Thank all of you very much, especially Nathan, Chris and Anshu.

cheers;

Ken



---------- Original Message -----------
From: Chris Daley <cdaley at flash.uchicago.edu>
To: Ken Chen <ken at asiaa.sinica.edu.tw>
Cc: Anshu Dubey <dubey at flash.uchicago.edu>, flash-users at flash.uchicago.edu
Sent: Tue, 10 Feb 2009 14:36:29 -0800
Subject: Re: [FLASH-USERS] compiling issue--error: too few arguments to	function 
[WINDOWS-1252?] $B![ (B5Dopen2? size=

> I think the reason FLASH is failing is because you have not promoted 
> reals to 8 bytes.
> 
> All floating point MPI communication in FLASH describes the data as type:
> FLASH_REAL = MPI_DOUBLE_PRECISION, so there is a mismatch in
> communication when you are using 4 byte reals.
> 
> Add the following flags to FFLAGS_OPT, FFLAGS_DEBUG and FFLAGS_TEST:
> -fdefault-real-8 -fdefault-double-8
> 
> Chris
> 
> Anshu Dubey wrote:
> > Ken,
> >
> > Your code is crashing at the first instance of MPI use after MPI initialization.
> > The routine nameValueLL  creates an MPI datatype, and then has several
> > MPI_bcast calls. Could you try a simpler mpi program to verify that it is not
> > your installation that is the problem ?
> >
> > Anshu
> >
> > On Tue, Feb 10, 2009 at 2:06 PM, Ken Chen <ken at asiaa.sinica.edu.tw> wrote:
> >   
> >> Hi Nathan and all:
> >> I tried the both sedov and sod problems. They worked fine for single cpu, but 
didn't
> >> work multi cpus. Is there a problem in open-mp or mpi stuff? I can compile the
> >> problems with these setups(mpi, open-mp) in Makefile.h. May something go wrong ?
> >> Thanks for any comment.
> >>
> >> cheers;
> >>
> >> Ken
> >>
> >>
> >> ---------- Original Message -----------
> >> From: Nathan Hearn <nhearn at ucar.edu>
> >> To: Ken Chen <ken at asiaa.sinica.edu.tw>
> >> Cc: flash-users at flash.uchicago.edu
> >> Sent: Tue, 10 Feb 2009 12:22:49 -0700
> >> Subject: Re: [FLASH-USERS] compiling issue--error: too few arguments to function
> >> [WINDOWS-1252?] $B![ (B5Dopen2? size=
> >>
> >>     
> >>> Hi Ken,
> >>>
> >>>     I'm sorry about that ... I read through your message too quickly.
> >>> It is difficult to ascertain the problem from the error messages, as a
> >>> segmentation fault can occur in many places.  Which setup are you
> >>> trying to run?  (And have you tried any of the other setups, such as
> >>> Sod or Sedov)?
> >>>
> >>> - Nathan
> >>>
> >>> P.S., Please be sure to reply to the flash-users list so that others
> >>> can offer advice.
> >>>
> >>> 2009/2/10 Ken Chen <ken at asiaa.sinica.edu.tw>:
> >>>       
> >>>> Hi Nathan:
> >>>> Thanks for prompt reply. Maybe you misunderstood my question, I am curious that 
I
> >>>>         
> >> can
> >>     
> >>>> run single cpu for flash on our machine (32 cpus work station). However, if I 
want
> >>>>         
> >> to run
> >>     
> >>>> more than 1 cpu such a  2,4,even 32. However I got the error message from 
below. I
> >>>> don't understand where the problem came from. Could you take a look the error
> >>>>         
> >> message
> >>     
> >>>> and give me some comments? Thanks a lot~~
> >>>>
> >>>> cheers;
> >>>>
> >>>> Ken
> >>>>
> >>>> *******************************************
> >>>> [ken at c object]$ mpirun -np 2 flash3
> >>>>  RuntimeParameters_read:  ignoring unknown parameter "iProcs"...
> >>>>  RuntimeParameters_read:  ignoring unknown parameter "jProcs"...
> >>>>  RuntimeParameters_read:  ignoring unknown parameter "kProcs"...
> >>>> [c:31677] *** Process received signal ***
> >>>> [c:31677] Signal: Segmentation fault (11)
> >>>> [c:31677] Signal code: Address not mapped (1)
> >>>> [c:31677] Failing at address: 0x3200000011
> >>>> [c:31677] [ 0] /lib64/libpthread.so.0 [0x3317c0f0f0]
> >>>> [c:31677] [ 1] /usr/lib64/openmpi/1.2.4-gcc/libopen-pal.so.0(_int_malloc+0x19c)
> >>>> [0x327882d2dc]
> >>>> [c:31677] [ 2] /usr/lib64/openmpi/1.2.4-gcc/libopen-pal.so.0(malloc+0x8f)
> >>>>         
> >> [0x327882ebcf]
> >>     
> >>>> [c:31677] [ 3] flash3(__namevaluell_data_MOD_namevaluell_addreal+0x92) 
[0x4fbb92]
> >>>> [c:31677] [ 4] flash3(namevaluell_bcast_+0x6b1) [0x4fb481]
> >>>> [c:31677] [ 5] flash3(runtimeparameters_init_+0x83) [0x44e573]
> >>>> [c:31677] [ 6] flash3(driver_initflash_+0x4a) [0x42f9ea]
> >>>> [c:31677] [ 7] flash3(MAIN__+0x1a) [0x43282a]
> >>>> [c:31677] [ 8] flash3(main+0x2c) [0x5d97ec]
> >>>> [c:31677] [ 9] /lib64/libc.so.6(__libc_start_main+0xe6) [0x331701e576]
> >>>> [c:31677] [10] flash3 [0x42b529]
> >>>> [c:31677] *** End of error message ***
> >>>> mpirun noticed that job rank 0 with PID 31676 on node c.spa.umn.edu exited on
> >>>>         
> >> signal 15
> >>     
> >>>> (Terminated).
> >>>> 1 additional process aborted (not shown)
> >>>> ******************************************************************
> >>>>         
> >> ------- End of Original Message -------
> >>
> >>
> >>
------- End of Original Message -------